Riemenspanner Belt tensioner
Riemenspanner Belt tensioner
Published 2020-04-28T14:58:34+00:00
serves to tension the belt when the threaded rods are aligned.
with the M3 screw and the groove stone, which engages by turning, everything can be fixed in place perfectly.
only parts that are included in the printer packaging are required
1x M5 screw
1x slot nut
1x M3x12 screw
1x hard rubber roller
more tension by mounting the tension block more to the side
Make sure that the belt runs cleanly on the roller and is centered in the tension block
the number indicates the centre distance to the beam.
I recommend to use 42
if it is too tight, 39 can be used
if this is still too much please let me know and I will upload more variants
Assembly
1. Z Move axis to reference
2. make sure that the lead screw is centered in the hole of the angle
3. move Z axis to 400
4. make sure that the lead screw is centered in the hole of the angle
5. completely loosen the toothed belt wheels on both sides (if the motors are still supplied with power, they will keep their position and there is no need to realign them)
6. Mount the M3 screw and the slot nut
7. put the tension block around the rear toothed belt and mount the wheel
8. install the tensioner in the middle position and place the belt on the wheel
9. Push to the side until the belt is tensioned but the lead screws do not bend
10. Tighten the toothed belt wheels again with the worm screws
11. Tighten the M3 screw so that the clamping block does not move
##########German#################
dient zum spannen des Riemens bei ausgerichteten Gewindestangen.
Mit der M3 Schraube und dem durch Drehung einrastenden Nuten stein kann alles sauber fixiert werden
benötigt werden nur Teile, die der Verpackung des Druckers beiliegen
1x M5 Schraube
1x Nutenstein
1x M3x12 Schraube
1x Hartgummi-rolle
gespannt wird indem der Spann-block mehr zu Seite versetzt montiert wird
es ist darauf zu achten, dass der Riemen sauber auf der rolle lauft und mittig im Spann-block läuft
die Nummer gibt den Achsabstand zum Träger an.
ich empfehle 42 zu verwenden
wenn es zu fest ist, kann 39 benutzt werden
wenn das immer noch zu viel ist bitte melden dann lade ich weitere varianten hoch
Montage
1. Z Achse auf Referenz fahren
2. schauen dass die Leitspindeln sich mittig in der Bohrung des Winkels befindet
3. Z Achse auf 400 fahren
4. schauen dass die Leitspindeln sich mittig in der Bohrung des Winkels befindet
5. Zahnriemenräder auf beiden Seiten komplett lösen (wenn die Motoren noch mit strom versorgt sind behalten diese ihre Position und es muss nicht neu ausgerichtet werden)
6. die M3 schraube und den Nutenstein montieren
7. den Spannblock um den hinteren Zahnriemen legen und das Rad montieren
8. den Spanner in Mittellage montieren und den Riemen auf das Rad legen
9. so weit zur Seite schieben bis der Riemen spannt aber die Leitspindeln sich nicht biegen
10. die Zahnriemenräder wieder mit den Wurmschrauben spannen
11. die M3 schraube anziehen damit sich der Spannblock nicht verschiebt
https://www.youtube.com/watch?v=CsdUrqBxIb0
outer wall should have 1.2-1.5mm
Filling approx. 15
no support is required
the 5mm hole can be redrilled if the screw does not fit
##########German#################
Ausenwand sollte 1.2-1.5mm haben
Füllung etwa 15%
es wird kein support benötigt
die 5mm bohrung kann nachgebohrt werden wenn die schraube nicht passt
Date published | 28/04/2020 |
Benoetigte Zeit | 60 - 107 Minuten |
Menge an Filament | 20 |
Dimensionen | 65.7 x 40.5 x 37.1 |
Support Free | YES |