"8-Bit" Minecraft Diamond Ore Lamp - Siri Enabled
"8-Bit" Minecraft Diamond Ore Lamp - Siri Enabled
3D
Published 2019-08-28T17:26:06+00:00
I've seen other Minecraft diamond ore lamps in various places by they all seem to lack the definitive pixelation that Minecraft embraces.
By leveraging techniques used from 3D printed lithographs and some of the features of the latest PrusaSlicer, I was able to give mine all the glorious 8-bit-ness it needs.
The lamp can be controlled via Siri (and its analogy on other platforms, I presume) via Homebridge.
Via the Home app on my iOS devices, I can easily control the color, brightness and on/off state at will with the familiar interface that I use with other devices.
Or, I can use the Siri commands:
"Hey Siri, turn the Diamond lamp on."
"Hey Siri, set the brightness of the Diamond lamp to 100%"
"Hey Siri, set the color of the Diamond lamp to [insert any color you like here!]" or
"Hey Siri, set the color of the Diamond lamp to Aqua" to get back to the desired Diamond Ore look.
Here's a video: https://youtu.be/6jC8ryEkgvQ
This is powered by a Raspberry Pi Zero and a Unicorn pHAT which offers an excellent about of lighting for this project and with a high level of flexibility.
I've even added a couple of bonus "colors" which are more like effect modes:
"Hey Siri, set the color of the Diamond lamp to Candlelight" will simulate a flickering candle inside the lamp.
"Hey Siri, set the color of the Diamond lamp to Ocean Boat Blue" will create a slowly undulating blue wave effect, and
"Hey Siri, set the color of the Diamond lamp to Razzmatazz" will create a cycling rainbow effect.
I've published the software I wrote to control the lamp and instructions for installing it here: https://github.com/mkoistinen/unicorn-homebridge-integration
This print measures 150mm on each edge.
If you're on a Prusa FDM printer and use PrusaSlicer print from the .3mf files from here (https://www.prusaprinters.org/prints/5175-8-bit-minecraft-diamond-ore-lamp-siri-enabled), it should just work. =)
In general, you'll need to print the following:
4x - 150mm Face (in gray) 4 x 5h14m
1x - 150mm Back Face (in gray) - 1 x 5h14m
1x - 150mm Base (in gray) - 1 x 5h28m
5x - 150mm Aperture (in white filament) - 5 x 2h6m
Estimated print time: ~42h, however, each of the prints is easy. There are no supports and everything is flat against the print bed.
The Base will provide four mounting pins for the RPi and the Back Face has a small hole near the bottom for the power cord.
Once printing is complete, the 5 apertures should just slide into some tiny brackets on the "inside" of each face. Once these are all in, each face snaps together with the next. Attach your RPi to the pins in the base (you may need to clean up the ends a little). Next, snap the base onto the remaining faces and you're done! It's a snug, semi-permanent fit when printed on my reasonably well-tuned Original Prusa i3 MK3S.
Note that the set of STL files also includes some "modifier" objects. These are referenced by the PrusaSlicer files (.3mf) to modify the print direction so that the flat faces have apparent "pixels" due to differing light effects. If you use another slicer that offers similar capabilities, use these modifier STLs to change the direction of the "fill" for only the bottom-most layer to 0°, 90°, and 135° for each of the modifier STLs and set the normal print direction for the unmodified layer to 45°.
I printed mine in Prusament Galaxy Silver (came with my printer) and white AmazonBasics Premium PLA and the results are gorgeous!
The photos don't do it proper justice.
| Date de publication | 28/08/2019 |
| Durée d’impression | 42 - 43 minutes |
| Dimensions | 150mm x 150mm x 150mm |
| Sans support | YES |