Hiya~

Been wanting to have a way to charge my Onewheel when out for a while. Since I have an electric bike I felt it would make sense to be able to use the battery from it on the battery pack. This is my 6th major iteration of a portable battery and hopefully my last, since it's up to my standard of simplicity and usefulness I figured now would be a good time to share with the community.

This allows me to fast charge the Onewheel on the go. It just fits in my backpack so allows me to keep floating for longer (hence the dumb name).

The design allows you to attach 2 36v 14.5Ah batteries back to back while using a solar charge controller to boost the voltage and safely charge the Onewheel. For more information on the topic of portable charging for the Onewheel visit the below.
https://onewheel.wiki/Charging_on-the-go

~ THINGS YOU'LL NEED ~

• A drill
• Soldering Iron and solder
• Philips screwdriver
• Allen keys
• 2x Rail_Mount.stl
• 1x MPPT_Mount.stl
• 2x Wire_Cover.stl
• 1x Handle.stl
• 2x 36v 14.5Ah ebike batteries (https://www.amazon.co.uk/dp/B07NV9ZZFG). There is a 12Ah version which is much cheaper if you don't need crazy amounts of juice.
• 1x MPT 7210A Solar Controller (https://www.amazon.co.uk/dp/B07J3W79DB)
• 6x M5 x 25mm Pozi Pan Bolt (https://www.amazon.co.uk/dp/B07XFQ2NWC)
• 10x M5 x 22mm Countersunk Bolt (https://www.amazon.co.uk/dp/B07RWKPQ7H)
• 4x M5 x 16mm Countersunk Bolt (https://www.amazon.co.uk/dp/B07RYZ2NY3)
• 1x M5 x 90mm Cap Head Bolt (https://www.amazon.co.uk/dp/B01N2HPG7B)
• 21x M5 Hexagonal Nuts (https://www.amazon.co.uk/dp/B07BVX8QQ5)
• 4x M4 x 16mm Pozi Pan Bolt (https://www.amazon.co.uk/dp/B07BGCQ6BF)
• 4x M4 Hexagonal Nuts (https://www.amazon.co.uk/dp/B07MLP2C2W)
• 1x 3mm x 100mm Steel Rod (https://www.amazon.co.uk/dp/B00OK6GD9M)
• 1x 16AWG insulated wire (https://www.amazon.co.uk/dp/B07FN9G27L)
• 1x XLR cable (https://www.amazon.co.uk/dp/B0151R409S)
• 1x XT60 male and female connectors (https://www.amazon.co.uk/dp/B074RGT76J)
  
  
  ~ ASSEMBLY ~

Printing

1. Print the Rail_Mount.stl twice. DO NOT MIRROR this part, it is designed to rotate after the print and bolt together.

2. Print the MPT_Mount.stl as is, this should not require support.

3. Print the Handle.stl. This may require support for the top overhang.

4. Print the Wire_Cover.stl twice. This may require support for the central overhang.

Adding Nuts

1. Take 3 nuts and place onto the central column of the Rail Mount leaving a gap between each. So from one end you might go nut, space, nut, space, nut, space. If the nuts don't quite fit use a bolt to pull the nut in from the other side.

2. Do the same on the other Rail Mount but with the opposite pattern, such as space, nut, space, nut, space, nut.

3. On the other sides of each Rail Mount add 2 nuts to each on the outer corners.

4. Perform a dry fit by placing the 2 rails together so that the nuts on the central column are not visible. Take the 4 M5 x 22mm Countersunk Bolts and fasten the 2 Rail Mounts together at the corners where there are 2 countersunk holes on each corner for both rails.

5. Rotate the rails so that the seem is now facing up. Both sides are the same so choose 1 and set that as your top. On the underside of the holes should be spaces to add a total of 10 nuts (ignore the ones on the bottom, those will be unused). Add the 10 nuts in the premade holes.

6. Take the MPT Mount and add the 4 M4 nuts to the underside.

7. Use the 4 M4 x 16mm Pozi Pan Bolts dry fit the MPPT Mount to the Rail Mount along the joining face you added nuts to the underside from earlier. The hole in the MPT Mount should align with the hole in the Rail Mounts with the XT60 hole pointing out of the shortest side.

8. Take the Handle and slide the 3mm rod down the small hole on the lower part of the Handle. It will be a tight fit so I suggest placing one end of the rod in a drill then using it to rotate the rod down. It will essentially melt its way down. Just before it reaches the other side saw off any excess and then tap the rest in till it's flush that side with none poking out the other side. This will add some shear strength to the lower part of the handle where the bolts sit.

9. Add an M5 Nut to the Handle in the premade hole, then screw down the M5 x 90mm Cap Head Bolt until it's threaded onto the nut. This doesn't need to be tight. If you do tighten it you may break the plastic. This is designed to add further shear strength to the upper part of the handle.

10. Add 6 M5 x 22mm Countersunk Bolts to the Handle and screw that down into the same side of the Rail Mounts as you did the MPT Mount. The taller side should be on the side of the MPT Mount.

Electronics

1. Make sure the batteries are removed from the battery rail.

2. The wiring that comes with the 36v 14.5Ah ebike batteries may not be long enough to reach the MPT controller so use the 16AWG wire to either extend it or replace it. 350-400mm should be long enough (from where it exits the rail all the way to the end). Tape them together with a label for later.

3. Solder 200-250mm of 16AWG wire to the male XT60 connector. I recommend putting the female end in the male connector while soldering to prevent the pins becoming misaligned. Tape them together with a label for later.

4. Thread the wire for the XT60 through the XT60 hole in the MPT Mount. Add some superglue to the lower sides of the XT60 and press it into the XT60 hole being sure to pull the wire through as you do as to not kink or trap it. It doesn't need to go all the way in.

5. Take the rails for the battery and pull the cables through the Rail Mounts so that the ends come out the hole in the MPT Mount.

6. Align the battery rails with the Rail Mounts. They should slot into the groove in which you can add 6 M5 x 25mm Pozi Pan Bolts (3 per rail) to fasten them down onto the rail mounts. Be sure to screw the the rails down in the correct nut. You want the nut to press up against that rail, not pull it out of the other rail. Tighten these down so that the rails are firm and won't risk detaching when carried.

7. Work the 6 wires (2 for the XT60 and 4 for the batteries) on the MPT Mount so that they follow the trench out to the side.

8. Using the Labels from earlier put the single positive wire for the XT60 in the positive battery terminal on the MPT controller. Then take the negative wire for the XT60 and connect that to the negative battery terminal on the MPT controller.

9. Take both positive wires for the batteries and connect them to the positive solar terminals on the MPT controller. Finally take both negaive wires for the batteries and connect them to the negative solar terminals on the MPT controller.

Charge Cable

1. Take the XLR cable and desolder the female end from the rest of it.

2. Cut some 16AWG wire to the length you want the charge cable to be. Mine is 1M for example.

3. Solder one end of the positive wire to pins 2 and 3 on the female XLR plug.

4. Solder one end of the negative lead to pin 1 on the female XLR plug.

5. Reassemble the XLR connector and slide up onto the wire any insulation/ sleeving/ heat shrink you want to use to complete the wire before adding the XT60.

6. Solder the positive terminal on the XT60 to the other end of the positive lead on the wire.

7. Solder the negative terminal on the XT60 to the other end of the negative lead on the wire.

8. Adjust the insulation/ sleeving/ heat shrink so that the charge cable is safe from shorting and no exposed wiring is visible.

Sanity Check.

1. Take a multimetre and set it to continuity test (with a beep if possible). Use this to probe between the positive and negative terminals of the XT60 to see if there is a short. Also test if there is a short across either of the battery rail connectors. Verify terminals on the MPT controller connect back to the correct place. Connect the charge cable to the XT60 on the MPT Mount and verify pins 2 and 3 on the XLR go back to the positive battery terminal on the MPT controller and that pin 1 goes back to negative. If anything is wired backwards, shorted or going to the wrong place now is the time to fix it! Failure to do this will end in tears.

Finishing Off.

1. Place the MPT controller on top of the MPT Mount so that the wires are pressed into the trench. If it does not sit flat try to move the wires so they do not overlap.

2. Take the 4 M4 x 16mm Pozi Pan Bolts and the 2 Wire Covers, placing the bolts into the 2 holes per wire cover.

3. Slot one over the side without the wires as this is the easiest. You should be able to put a screwdriver through the holes in the top of the over to eventually screw the covers down through the MPT mount and into the nuts on the underside of the MPT Mount.

4. Do the same with the other side that has the wires, be careful not to trap any of the wires or damage the insulation. Apologies that this step might be utterly infuriating trying to wiggle the screwdriver and bolt around the wires.

MPT Programming And Final Test

1. Slot 1 battery onto the battery rail and use the key to lock it in place so it doesn't slide off onto your foot.

2. Power it on and check the MPT controller turns on.

3. Program the MPT controller to the desired voltages and max current settings.I recommend reading the manual thoroughly on all settings and warnings.

• You want to set the "solar" voltage to 36v assuming you used 36v batteries linked in above.
• For the Onewheel and Onewheel + you want to set the target voltage to 58v and current to 3.5A
• For the Onewheel + XR you want to set the target voltage to 63v and current to 3.5A
• For the Onewheel Pint you want to set the target voltage to 63v and current to 1.3A
  You can charge at a higher current but battery longevity can be shortened plus the wiring may become hotter with currents above this. Too hot and they could melt and short out.

4. With the settings dialled in connect the other battery and verify that when it is powered on that everything still works with no magic smoke.

5. Connect the charge cable and verify if the desired voltage is present on the XLR. Set your multimetre to DC voltage and place the negative probe in pin 1 and then the positive in pin 2. Verify the voltage and then try the positive probe in pin 3. If all looks good connect it up to your onewheel.

6. Open the Onewheel app and check the board is charging. The current on the MPT will climb steadily until it reaches a point in which it is happy for the current voltage. As the board charges the voltage will climb closer to the target voltage you set whilst the current will get lower and lower until it's met the target voltage.

That should be it, enjoy your Lifejacket, may it keep you floating for many more miles.

Please share any improvements or thoughts as I'm more than happy to try and improve on this further :)