Spiral clock
Spiral clock
Published 2020-11-25T12:18:35+00:00
Please scroll down for the English version
Trovare l'idea per un orologio particolare non è stato facile ma appena mi è venuta in mente questa, mi sono messo subito a disegnarla.
Il funzionamento è molto semplice, l'orologio deve essere appeso alla parete o mantenuto con il quadrante verticale, con il passare del tempo il quadrante ruoterà facendo muovere la sfera. Essa si avvicinerà sempre più al centro e alle ore 12 circa cadrà nel foro che la riporterà sulla circonferenza esterna.
La movimentazione del quadrante non è possibile con un normale meccanismo per orologi visto che deve compiere 150° di rotazione in un ora invece che 360°, per cui ho preso un motore DC e ho provveduto a fare la corretta demoltiplica. La velocità di rotazione del motore (secondo il datasheet) è di 7700 rpm con una tensione applicata di 2,4V (link), di conseguenza la riduzione è stata progettata in modo che compisse solo 150° in un ora, il primo stadio di riduzione è 1/125 (verde-giallo), il secondo e il terzo stadio sono 1/6 (giallo-rosso e rosso-blu), il quarto stadio è 1/7 (blu-arancione) e il quinto stadio è 1/33 (arancione-oro).
Non è un progetto definitivo, anzi, chiunque abbia suggerimenti o proposte di miglioramenti sono molto felice di ascoltarlo. Sicuramente è possibile mettere un controllo tramite un semplice encoder così da avere un orologio preciso a distanza di giorni, oppure utilizzare un motore passo passo o un servo motore opportunamente controllati.
Buona stampa!
Finding the idea for a particular watch was not easy but as soon as it occurred to me, I immediately started to draw it.
The working is very simple, the clock must be hung on the wall or maintained with the vertical dial, over time the dial will rotate causing the ball to move. The ball will get closer and closer to the center and at about 12, it will fall into the hole that will bring it back to the outer circumference.
The motion of the dial is not possible with a normal clock mechanism since it has to rotate 150° in one hour instead of 360°, so I took a DC motor and proceeded to do the correct demoltyping. The rotational speed of the motor (according to the datasheet) is 7700 rpm with an applied voltage of 2.4V (link), consequently the reduction was designed so that it only completed 150° in an hour, the first reduction stage is 1/125 (green-yellow), the second and third stages are 1/6 (yellow-red and red-blue), the fourth stage is 1/7 (blue-orange) and the fifth stage is 1/33 (orange-gold).
It is not a final project, anyone who has suggestions or proposals for improvements, I'm very happy to hear it. Surely it is possible to put a control through a simple encoder so as to have a precise clock after days, or use a step-by-step motor or a properly controlled servo motor.
Happy printing!
Print all parts with high quality to have a great end result.
The printing support is only needed for "supporto.stl".
Take all the printing part and:
- 1 Dc motor
- 6 screw M3x28
- 3 screw M3x16
- 2 screw M3x10
- 1 screw M3x26
- 12 nut M3
- 1 screw M4x40
- 1 nut M4
- glue
Clean all the part accuracy before assemby.
Mount in this order the mechanism (see components photo).
On the white support:
1 - Object red + 1 bolt M3x10 (right) + 1 bolt M3x16 (left)
2 - Object blue + 1 bolt M3x26
3 - Object orange + 2 bolts M3x16
4 - Object yellow + bolt M4x40
5 - Object green + 1 bolt M3x10
6 - DC motor
On the dial:
1 - pipe + gear + 6 bolt M3x28
2 - glue black spiral on the dial
Now assembly the two part and it's finish!
Date published | 25/11/2020 |
Tempo per farlo | 1200 - 1500 Minuti |
Quantità di filamento | 100g |
Dimensioni | 160mmx160mmx75mm |