Hi, this is my creation
a Raspberry PI 4 laptop, it as everything u need
4 usb port, ethernet, wi fi, 2 speakers, 3.5 jack for music ecc

Is all printe in PETG, 13.3"

if you are crazy like me, make this project, is a bit expensive

in the photos you will see some "errors" like holess etc, the STL files i uploaded are all corrected

ill link all the part i used

you will need a solder, a multimeter, a 3d printer and a lot of money and time, and some
paint

For the compoent list, number of print and position, check the Portatile.STEP file

all the file below take referece of the Step file:

-raspberry pi 4 model b 4gb = raspberry pi 4 (any ram model, i use 4gb but obv the 8gb is better) + https://www.amazon.it/gp/product/B07JGNF5F8/ref=ppx_yo_dt_b_asin_image_o05_s00?ie=UTF8&psc=1

-pi keyboard =
https://www.amazon.it/gp/product/B07RT1NBNH/ref=ppx_yo_dt_b_asin_image_o07_s00?ie=UTF8&psc=1 (use ur language)

-trackpad = https://www.amazon.it/gp/product/B07JM7FWR9/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1

-Step Down voltage regulator LM2596 =https://www.amazon.it/gp/product/B01B7BQZJK/ref=ppx_yo_dt_b_asin_image_o08_s00?ie=UTF8&psc=1

-pulsantiera+pcd lcd+13.3" = https://it.aliexpress.com/item/32842409539.html?spm=a2g0s.9042311.0.0.27424c4d7xuFXi

-tondo aisi = a Ø10x300 h9 shaft i fount in the company i work, you can make it wood or plastic, but is better in steel for a better quality (is the rotating shaft of the laptop to close and open it)

-batteria = is the custom battery, 3x18650 (i used samsung) in series (12v) + a PCB, u will see in the photo https://www.amazon.it/gp/product/B075MGPM98/ref=ppx_yo_dt_b_asin_image_o08_s00?ie=UTF8&psc=1

-hub= https://www.amazon.it/gp/product/B00Y25XFGK/ref=ppx_yo_dt_b_asin_image_o06_s00?ie=UTF8&psc=1

-speaker new = https://www.amazon.it/gp/product/B07TP99MPD/ref=ppx_yo_dt_b_asin_image_o02_s00?ie=UTF8&psc=1

-voltimetro = https://www.amazon.it/gp/product/B07MJKFR1Q/ref=ppx_yo_dt_b_asin_image_o05_s00?ie=UTF8&psc=1

-ethernet= https://www.amazon.it/gp/product/B07TWHDHYN/ref=ppx_yo_dt_b_asin_image_o06_s00?ie=UTF8&psc=1 + a really short lenght (10cm ethernet cable)

-scheda audio = https://www.amazon.it/gp/product/B00SLYAK1G/ref=ppx_yo_dt_b_asin_image_o04_s00?ie=UTF8&psc=1

-cables ecc.=
-to recharge laptop=
https://www.amazon.it/gp/product/B00E8CURKO/ref=ppx_yo_dt_b_asin_image_o06_s00?ie=UTF8&psc=1
you will need a power supply too, i use a old laptop one (12v)

-audio 3.5, from raspberry to the case=
https://www.amazon.it/gp/product/B07RRZYZFV/ref=ppx_yo_dt_b_asin_image_o06_s00?ie=UTF8&psc=1

-a lot of screws=
https://www.amazon.it/gp/product/B07748JK1H/ref=ppx_yo_dt_b_asin_image_o04_s00?ie=UTF8&psc=1

-you need the Type C usb male to connect the battery no the pi 5v=
https://it.aliexpress.com/item/33055417046.html?spm=a2g0s.9042311.0.0.27424c4d7xuFXi

-cable to connect the lcb pcb to raspberry=
https://www.amazon.it/gp/product/B07P53NPWR/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1

-cable from 13.3" to his pcb, because the one they give you is too short
(care for cinese low priced, they will insta melt) (use at least 400/500mm)=
https://www.ebay.it/itm/30-PIN-0-5mm-Pitch-AWM-20624-80C-60V-VW-1-Flexkabel-500mm-Typ-B/174189024373?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m1438.l2649

i probably left something behind, if you have question contact me
and follow C4ssius.creations on instagram
https://www.instagram.com/c4ssius.creations/